- Recent
- Popular
- Answered
- Unanswered
0helpful
1answer
It sounds like the power surge coming back on damaged the controller. Try disconnecting the mains supply overnight to fully dissipate all voltage in the electronics. It that doesn't work, this is the maker, reach out for support.
Wide Selection of Topside Panels
Balboa Water Group -https://www.balboawatergroup.com > Spa ProductsElectronic Controls · Slimline® Jet Collection · Bath Jets · Zen Look Collection ... Balboa the largest manufacturer of hot tub panels in the world. These panels .....
Read full answer
9/26/2023 1:49:51 AM ••77 views • 0 helpful votes
1helpful
1answer
On the control unit select the 'up' arrow to cycle through the LED lighting options. Some units will only have one option (Blue) while other models will have a spectrum of colours to select from. Control unit diagram illustrated here https://www.hottubhiremerseyside.co.uk/faqs/
Read full answer
10/11/2023 2:11:02 PM ••42 views • 1 helpful votes
0helpful
1answer
possible water flow problem in spa mode
Read full answer
10/10/2023 5:19:17 PM ••42 views • 0 helpful votes
0helpful
1answer
2 'hot wires'? Don't mess with 220 volts and water that you are going to immerse yourself in. Call and electrician or the pool company and do it properly to current electrical code by a qualified professional.
Read full answer
9/8/2023 9:53:53 PM ••46 views • 0 helpful votes
0helpful
1answer
Paul,Found this info...https://www.justanswer.com/pool-and-spa/fpr35-rheem-pool-heater-hp6-error-code-no-clue.htmlBest to you
Read full answer
8/17/2023 12:57:12 PM ••73 views • 0 helpful votes
0helpful
1answer
Maybe a call to their coustomer support 888 #.Ck here.....https://images.inyopools.com/cloud/documents/dolphin-troubleshooting-guide.pdf
Read full answer
5/22/2023 9:21:20 PM ••380 views • 0 helpful votes
0helpful
1answer
You didn't give us a Make and Model but here are some sites that answer that question for varied Makes..https://www.google.com/search?q=digital+pool+heater+is+displaying+sw+open+error&source=hp&ei=ZoKPZO-nHLfF0PEP0-iW6A8&iflsig=AOEireoAAAAAZI-QdpNy-irsShPIybO1gAWJJK1zy3Tx&oq=digital+pool+heater+is+displaying+sw+open&gs_lcp=Cgdnd3Mtd2l6EAEYADIFCCEQoAEyBQghEKABUABYAGDsM2gAcAB4AIABjAKIAYwCkgEDMi0xmAEAoAECoAEB&sclient=gws-wiz
Read full answer
6/18/2023 9:18:13 PM ••170 views • 0 helpful votes
0helpful
1answer
google Mastercraft jet pump Model #561471 partsIf it as described I would put new pump in. If you chose rebuild it A new is is $250 on eBay.
Read full answer
6/26/2023 12:15:58 PM ••101 views • 0 helpful votes
0helpful
1answer
Try here;https://www.manualslib.com/products/Caldera-Tahitian-6976269.html
Read full answer
8/15/2023 7:32:46 PM ••31 views • 0 helpful votes
0helpful
1answer
no info generic answer when pump is on [to make temp ] the jets are also on
Read full answer
7/21/2023 4:20:00 PM ••52 views • 0 helpful votes
0helpful
1answer
circulation pump failure
Hot Tub Error Codes - Spa Topside Error Messages
Hot Tub Essentialshttps://www.hottubessentials.ca > hot-tub-error-codes1) Hot Tub Error Codes (Alphabetical) ; COOL, Spa water is more than 20° F cooler than the temperature set point ; CP-ER, Circ pump failure ; DR, dr, dy?
Read full answer
6/29/2023 8:11:43 PM ••88 views • 0 helpful votes
0helpful
1answer
Tony,Ck these sites on how to identify it...https://duckduckgo.com/?t=ffab&q=hot+tub+idendifierBest to you.
Read full answer
7/15/2023 7:45:48 PM ••47 views • 0 helpful votes
0helpful
3answers
If the controller for your Prowler 920 robotic pool cleaner is not turning on or powering up properly, here are a few steps you can take to troubleshoot the issue:1. Check the Power Supply: Ensure that the power supply is properly connected to the controller and that it is receiving power. Verify that the power cord is securely plugged into a functioning power outlet. You can try plugging another device into the same outlet to confirm that it is working correctly.2. Inspect the Controller Display: Take a close look at the display on the controller. If any error codes or messages are displayed, consult the user manual or contact the manufacturer for further instructions on how to resolve the specific issue indicated.3. Reset the Controller: Try performing a reset on the controller. Look for a reset button or a combination of buttons to press and hold simultaneously for a few seconds. This action can often help resolve minor software glitches and restore the controller's functionality.4. Check for Loose Connections: Ensure that all cables and connections between the controller and the power supply or the Prowler unit are securely plugged in. Sometimes, a loose or faulty connection can prevent the controller from turning on.5. Replace Batteries: If your controller uses batteries, make sure they are not depleted. Try replacing the batteries with fresh ones and see if the controller powers up properly.6. Contact Manufacturer Support: If the above steps do not resolve the issue, it's recommended to reach out to the manufacturer's customer support. They can provide you with further assistance, troubleshooting steps, or advise on any potential repairs or replacements that may be needed.Remember to consult the user manual that came with your Prowler 920 for any specific troubleshooting steps or contact information for customer support.
Read full answer
5/22/2023 9:23:13 PM ••182 views • 0 helpful votes
0helpful
1answer
Read full answer
8/1/2023 9:17:04 AM ••32 views • 0 helpful votes
0helpful
1answer
Question edited to add full 'make model (what it is)'.Question moved from Washing Machines Category..Yes, the manual says blocked drain. Force a garden hose jet of water down it. It says to allow the control unit to auto reset, but try a forced reset.Page 29https://www.allswimltd.com/pdf/Genie-S-Operating-Installation-and-Servicing-Instructions.pdfhttps://www.google.com/search?q=certikin+genie+service+reset..
Read full answer
5/14/2023 4:32:27 PM ••117 views • 0 helpful votes
1helpful
1answer
See page 18 of the saltwater instruction guide ... 93 means it is on stand-by, power saving mode. Nothing is wrong, it's just waiting for the timer to tell it to turn back on automatically. If you want the system to be on right now, just turn the power switch off, wait a couple seconds and turn it back on.
Read full answer
6/12/2023 8:30:33 AM ••49 views • 1 helpful votes
0helpful
1answer
If your Certikin Genie pool heater is displaying an error code "HI" indicating a blocked condensate, but you have checked for blockages and the sensor appears to be functioning correctly, there are a few additional troubleshooting steps you can try:
- Check the condensate drain line: Ensure that the condensate drain line is clear and not blocked. Sometimes debris or dirt can accumulate in the drain line, causing a blockage. Use a thin brush or pipe cleaner to clean out any potential obstructions.
- Inspect the condensate trap: The condensate trap is a component in the heater's condensate system that collects and removes condensation. Check the condensate trap for any blockages or debris. Remove any obstructions and clean the trap thoroughly.
- Verify the exhaust system: Make sure the exhaust system, including the vent pipe and termination point, is clear of any obstructions. Blockages in the exhaust system can cause condensate backup. Inspect the vent pipe for any signs of damage or clogs and address any issues found.
- Reset the system: Try resetting the pool heater to see if it resolves the error code. Consult the manufacturer's manual or instructions for the specific steps on how to reset the heater. This can sometimes clear temporary faults or errors.
- Contact technical support: If you have performed the above steps and the error code persists, it's recommended to contact Certikin's technical support or customer service for further assistance. They can provide specific troubleshooting guidance or recommend a qualified technician who can diagnose and fix the issue.
It's important to note that working with pool heaters involves dealing with potentially hazardous systems and components. If you are not experienced or comfortable with troubleshooting pool heaters, it's best to seek professional help from a certified technician or contact the manufacturer for support.
Read full answer
5/14/2023 4:40:11 PM ••60 views • 0 helpful votes
0helpful
1answer
Generic help in the linkhttps://www.google.com/search?q=power+button+blinking.+And+will+not+make+salt+into+chlorine..
Read full answer
5/13/2023 2:38:57 PM ••33 views • 0 helpful votes
0helpful
1answer
If the control panel indicator lights on your pool system do not consistently light up when the pool is turned on, it could indicate a potential issue with the control panel or the electrical connections. Here are some troubleshooting steps you can take:1. Check Power Supply: Ensure that the power supply to the control panel is stable and consistent. Make sure the power source is providing the correct voltage and that there are no loose or faulty connections.2. Inspect Wiring Connections: Verify that all wiring connections to the control panel are secure and properly connected. Loose or damaged wiring can cause intermittent issues with the indicator lights.3. Clean and Inspect Control Panel: Check the control panel for any signs of dirt, debris, or corrosion. Clean the control panel and its components using a soft cloth and a mild cleaning solution. Inspect for any visible damage or loose components.4. Test Indicator Lights: While the pool is running, observe the control panel and try to identify any patterns or triggers that may cause the indicator lights to come on. Gently tap on the control panel to see if it affects the lights. This could indicate a loose connection or a faulty component within the control panel.5. Consult a Professional: If the issue persists or you are unable to identify the cause of the inconsistent indicator lights, it is recommended to contact a professional pool technician or the manufacturer's customer support for further assistance. They will have the expertise to diagnose and resolve the specific issue with your pool control system.Remember, working with electrical components requires caution. If you are not experienced or comfortable working with electrical systems, it is best to seek professional help to avoid any potential safety hazards.
Read full answer
4/6/2023 7:12:14 PM ••63 views • 0 helpful votes
0helpful
3answers
No service manual unfortunately
Sundance 2004 850 Owner's Manual (60 Hz) - The Spa Works
The Spa Workshttps://www.thespaworks.com > sites > default > filesPDFThe Sentry control system allows you to easily adjust two separate aspects of circulation pump operation: 1. The time of day (start time) the circulation pump ...
Sundance 850 Series Owner's Manual (2000) - The Spa Works
https://www.thespaworks.com > sites > default > filesPDFOptional Checkmates™ Water Quality Monitor (850 Only).......... 28 ... Your Sundance hot tub is constructed to the highest stan- ... Sentry Control Box.
Read full answer
3/13/2023 9:44:24 PM ••113 views • 0 helpful votes
- Prev
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- Next
Not finding what you are looking for?
- Q & A
- Products